text.skipToContent text.skipToNavigation
456.24 Jowatac® Foam bonding adhesiveID45624
Spritzfähiger klassischer Lösemittelklebstoff von Jowat® für Polster- und Möbelwerkstoffe mit geringem Festkörpergehalt und niedriger Viskosität.

Prix sans Livraison, hors taxe TVA et COV si applicable.


Styrene copolymer adhesive for bonding foam materials, also molded foam and upholstery wadding to each other as well as to wood, hardboard, particleboard, cardboard, rubberized hair and other upholstery materials. Also for expanded polystyrene. Customer trials are required. The properties of the bonded parts and, where necessary, the primer coating on the reverse side of the materials have to undergo application-related testing prior to use.

Characteristics / Directions for Use:

Good spraying properties, good initial adhesion, practically no residual tack, good heat resistance. Application on both surfaces by spraying. To be processed from pressurized container or barrel pump either directly or via a circulation system. Avoid all contact of pressurized container, pump and ductwork with galvanized metals or zinc alloys. The adhesive reacts aggressively with the metal and can no longer be used. Requirements for a High-Quality Bonding Process: The properties (e.g. surface tension, plasticizer content…) and the conditioning of the substrates, as well as the processing conditions (e.g. ambient temperature, humidity…) will influence the processes of joining and the bonding. Customer tests under consideration of everyday production conditions are therefore absolutely necessary to define stable process parameters and to ensure that the product is fit for purpose. For best bonding results, the materials to be bonded should be free of dust, oil, and grease, and be dry. Avoid draft. Our Application Technology Department and our Application Specialists will provide technical data to assist you in your choice of an appropriate product for your requirements. Please observe the information in the section “Remarks.” As a suggestion on how to establish high-quality bonding processes, please refer to DIN 2304.


Jowat® Cleaner 403.40. Safety Considerations: Safety Considerations: Observe the safety data sheet. Extraction and ventilation are required especially if an open application system is used.


The product should remain stored in properly closed original containers, dry and cool (15 – 25 °C). For best-before date, please see container label. After the elapse of the best-before date, it is essential that you again verify that the product is fit for your intended application.


Information about packaging types and units is available upon request.


For further information concerning safety, handling, transport and disposal, please refer to the safety data sheet. The information on this data sheet is based on test results from our laboratories as well as on reported experience gained in the field by our customers. It can, however, not cover all parameters for each specific application and is therefore not binding upon Jowat, nor should it be relied upon in lieu of your own required testing. The information given in this leaflet does not represent a performance guarantee. Unless otherwise agreed with our customers, the values stated in the section “Specification” shall be regarded as the finally agreed upon product properties. No liability may be derived from the information contained herein nor from the information provided by our free technical advisory service.

For the complete technical data sheet click here

Please refer to the "Download" tab for the safety data sheet.

Base Styrol-Copolymer
Processing temperature 15 - 25 °C
Density at +20 °C [g/cm³] at 20 °C [g/cm³]: 0.81 ± 0.03 ( pycnometer, 50 ml)
Viscosity at 20 °C [mPas] 225 ± 25 ( Höppler, ball 4)
Open time at 20 °C / 50% RH [min] 0,5 - 15 Minuten (zweiseitiger Auftrag)
Solids content 38,0 ± 2,0 % (2 h bei 90 °C, Jowat Prüfmethode)
Material pressure 0,5 - 3 bar
Injection pressure 4 - 6 bar
Diameter 1 - 1,5 mm